How to select the product H1400 for high-temperature sealing?

Hits: 693 img

One cannot simply conclude that product H1400, a silicone resin adhesive of the hydroxyl type, is suitable for all high-temperature sealing systems between engine blades and hubs based solely on its long-term temperature resistance exceeding 325°C, or the fact that the adhesive layer does not crack or powder at 400°C for 50 hours of aging. Product H1400 is a solvent-containing, single-component silicone resin adhesive. One must first confirm the type of substrate and surface treatment, solvent dilution and evaporation conditions, adhesive layer thickness, 300°C × 2-hour curing curve, operating temperature and atmosphere, thermal shock and vibration, sealing gap and pressure, and then determine whether the problem is caused by insufficient solvent evaporation, rapid temperature increase, thick adhesive layer, substrate contamination, insufficient curing, thermal mismatch, or poor matching with the sealing structure and operating conditions. Product H1400 can be considered as a candidate for high-temperature sealing, but it must be confirmed through small-scale tests, adhesive layer verification, and actual thermal cycling assessment.


1. Why do hydroxyl type sealants often crack or powder at high temperatures?


The substrate surface is not clean, with oil stains, oxide layers, release agents, or dust, which affects the wetting of the adhesive layer and interface adhesion.


The product contains solvents, and after application, the solvents do not fully evaporate before entering the high-temperature curing process. The intense evaporation of the solvents leads to blistering, pinholes, or cracking.


The curing temperature is too fast, and the internal contraction of the adhesive layer is inconsistent, resulting in internal stress, which expands into cracks under thermal shock.


The adhesive layer thickness is not controlled properly. If it is too thick, the solvents are difficult to evaporate and the thermal mismatch increases. If it is too thin, it does not fill adequately or is not continuously sealed.


The curing is not carried out according to 300°C × 2 hours, and the degree of crosslinking or ceramicization is insufficient, making it prone to powdering or losing adhesion at high temperatures.


The operating temperature is often above 325°C or local overheating, exceeding the long-term tolerance range of silicone resin adhesives.


There is vibration, thermal cycling, oil or gas contact between the engine blades and hubs, and the adhesive layer is subjected to dynamic stress and medium influence. No actual operating conditions have been verified.


The sealing gap, flange pressure, or structural displacement do not match the elasticity of the adhesive layer, and after thermal cycling, adhesion failure or sealing failure occurs.


Switching from phosphate sealants, borosilicon nitrogen-based adhesives, polycarbosilane adhesives, or other silicone resin sealants without adjusting the surface treatment, solvent dilution, adhesive layer thickness, and curing curve leads to performance deviations from the target.


Storage conditions do not meet the requirements of cool and dry storage or exceed the 6-month shelf life, resulting in a decrease in the adhesive material's activity, fluctuations in curing quality and high-temperature stability.


Poor ventilation in the operating environment affects the health of the operators and may mask changes in the adhesive material's state.


Insufficient understanding of the typical data of 400°C aging for 50 hours and 50 times of thermal shock at room temperature to 400°C, and failure to assess the safety factor based on the actual temperature, time, and cycle number of engine sealing.


2. Which stage does the cracking or powdering problem in high-temperature sealing occur?


Failure stage Possible causes Preferred inspection direction
Bubble or pinholes in the coating after application Insufficient solvent evaporation, excessive coating thickness, rapid temperature increase solvent evaporation time, coating thickness, temperature increase curve
Cracking of the adhesive layer after curing Excessive coating thickness, rapid temperature increase, mismatch of substrate thermal expansion coating thickness, temperature increase rate, substrate treatment
Insufficient adhesion after curing Unclean substrate, improper surface treatment, contamination of the adhesive layer surface cleaning, primer or pre-treatment, environmental cleanliness
Powdering after 400°C aging Insufficient curing, exceeding long-term temperature resistance, oxidation of the adhesive layer curing curve, operating temperature, atmosphere
Cracking or detachment after thermal shock Thermal mismatch, excessive coating thickness, structural displacement thermal expansion matching, coating thickness, sealing structure
Leakage of the sealing structure Non-continuous coating, pores, interface detachment coating process, curing curve, sealing gap
Thickening of the adhesive material or abnormal curing after storage High storage temperature, poor sealing, exceeding 6 months storage conditions, container sealing, shelf life
Batch-to-batch appearance or performance fluctuations Insufficient solvent ratio, rubber batch, coating and curing records Incoming inspection, dilution records, curing curve records
If only focusing on "whether product H1400 was used", but without records of substrate treatment, solvent evaporation, rubber layer thickness, curing curve, usage atmosphere and thermal cycling conditions, it is usually difficult to accurately determine whether it is a material issue or a process issue.


III. Why is it not necessarily effective to only increase the curing temperature or increase the rubber layer thickness?


Product H1400 plays a role as a high-temperature rubber layer in the sealing system. It is affected by the substrate, solvent, rubber layer thickness, curing curve, usage temperature and structure. Simply increasing the temperature or adding thickness may bring side effects.


Increasing the curing temperature may accelerate curing, but too rapid heating will cause the solvent to evaporate sharply, leading to blistering, pinholes or cracking.


Extending the curing time may improve the curing degree, but exceeding the recommended curve may lead to the rubber layer being too brittle or the substrate being damaged.


Increasing the rubber layer thickness may improve the filling capacity, but too thick will increase the difficulty of solvent evaporation and thermal mismatch, and be more prone to cracking or powdering.


Reducing the rubber layer thickness may reduce internal stress, but it may result in insufficient glue, pores or discontinuous sealing.


When the substrate surface is not cleaned, only adjusting the curing temperature or rubber layer thickness cannot solve the adhesion problem.


When the solvent is not fully evaporated, only increasing the curing temperature will exacerbate the risk of blistering and cracking.


When high-temperature oxidation or thermal cycling causes powdering, only increasing the curing temperature cannot restore the temperature resistance performance.


When the product has expired or the rubber material's activity has decreased, only adjusting the process cannot restore the original curing quality.


When the sealing structure has displacement or pressure, only increasing the rubber layer thickness cannot solve the problem of structural compatibility.


Therefore, when optimizing, one should observe substrate treatment, solvent evaporation, rubber layer thickness, curing curve, usage temperature and sealing structure, rather than only adjusting a single parameter.


IV. What are the differences in product H1400's selection priorities compared to similar high-temperature sealing solutions?


Comparison direction Product H1400 (siloxane sealant) Ordinary organic silicone sealant Phosphate high-temperature sealant Borosilicon nitrogen/ polycarbon silicon adhesive Inorganic ceramic sealant Selection boundary
Temperature resistance range Marked as longer than 325℃ in the data Usually 200-300℃ Up to 1000℃ or more Up to 1000-1500℃ or more Up to 1000℃ or more High-temperature structural bonding requires assessment of higher temperature systems
Number of components Single component Single component or dual component Usually single component or dual component Single component or dual component Varies by product Selection depends on construction and curing conditions
Solvent With solvent Varies by product Usually water-based or solvent-based Usually solvent-free Varies by product With solvent products require ventilation and evaporation control
Curing temperature 300℃×2 hours Room temperature or heating Medium-high temperature curing 170-220℃ or higher High-temperature sintering Select based on substrate temperature resistance and production line
Main function High-temperature sealing Elastic sealing High-temperature sealing/ bonding High-temperature structural bonding/sealing High-temperature sealing/coating Need to distinguish between sealing and structural bearing
Thermal shock performance Marked as 50 times of thermal shock from room temperature to 400℃ in the data Need verification Need verification Need verification Need verification Verify according to actual cycle times and heating/cooling rates
Rubber layer elasticity Silicone resin type, need verification Better elasticity Relatively brittle Relatively brittle or ceramicized Relatively brittle Select based on sealing structure displacement
Application scenarios High-temperature sealing between engine blades and hubs General high-temperature sealing High-temperature furnaces, pipeline sealing Graphite, ceramics, composite material bonding High-temperature equipment sealing Select based on temperature, structure and medium
V. What parameters should be confirmed when using product H1400?


Parameter category Information to be confirmed
Application direction High-temperature sealing between engine blades and hubs
Base material type: Metal blades, hubs and surface coating status
Surface treatment: Cleaning method, degreasing, removal of oxide layer, drying degree
Rubber material state: Colorless transparent liquid appearance, viscosity approximately 300 cp, whether it has exceeded 6 months
Solvent and dilution: Whether diluted, type of diluent, solvent evaporation conditions
Coating process: Coating amount, layer thickness, uniformity, whether multiple coatings are applied
Curing curve: 300℃ × 2 hours, heating rate and holding conditions
Operating temperature: Long-term temperature, peak temperature, local overheating conditions
Operating atmosphere: Air, gas, oil mist, oxidizing or reducing atmosphere
Thermal shock: Number of cycles from room temperature to 400℃, heating and cooling rate
Sealing structure: Gap, pressure, vibration, structural displacement, leakage requirements
Storage conditions: Cool and dry place, sealed, shelf life 6 months
Acceptance indicators: No cracking, no powdering, adhesion, sealing performance, retention rate of appearance and strength after thermal shock


Six. What should be mainly verified when using product H1400?


Wetting property of the base material surface after treatment and continuity of the rubber layer.


Solvent evaporation time and storage conditions after coating.


The influence of rubber layer thickness on blistering, cracking and sealing performance.


Appearance, adhesion and curing degree after 300℃ × 2 hours curing.


Changes in cracking, powdering and adhesion after 50 hours of 400℃ aging.


Cracks, detachment and sealing performance after 50 times of thermal shock from room temperature to 400℃.


Sealing reliability under vibration, pressure and structural displacement between engine blades and hubs.


Influence of oil mist, gas or oxidizing atmosphere on the rubber layer.


Consistency of different base materials and surface coatings.


Consistency of rubber material viscosity, solvent ratio and curing behavior between batches.


Changes in rubber material state and curing performance within 6 months of storage.


Impact of ventilation conditions and solvent evaporation on the operating environment.


Seven. How to design tests before using product H1400?


Establish a current high-temperature sealing agent benchmark, record model, surface treatment, dilution, rubber layer thickness, curing curve and failure performance.


Uniform test conditions: Base material, surface treatment, rubber dilution, coating amount, rubber layer thickness, curing curve, operating temperature, atmosphere and thermal shock conditions.


Set candidate samples: Current sealing agent, product H1400, different rubber layer thickness or curing curve gradients.


Complete the full process test: Surface treatment → coating → solvent evaporation → curing → appearance/adhesion → 400℃ aging → thermal shock → sealing performance test.


Evaluate actual results: No cracking, no powdering, adhesion, sealing performance, retention rate of appearance and strength after thermal shock.


Test items Uniform requirements
Base material and surface treatment Keep consistent or set gradients according to the test design
Rubber dilution and solvent evaporation Set gradients according to the test design
Rubber layer thickness Set gradients according to the test design
Curing curve Set gradients based on the 300℃ × 2h benchmark
Operating temperature Set nodes such as 325℃, 400℃ etc.
Operating atmosphere Set according to actual working conditions
Thermal shock conditions Set according to room temperature to 400℃, number of cycles and heating and cooling rate
Measurement methods Appearance, adhesion, sealing performance, cracking powdering, thermal shock retention rate are consistent
Eight. Under which circumstances should product H1400 not be directly used?


If the base material surface is not cleaned or has oil stains, oxide layer or release agent, it affects adhesion.


If the solvent cannot be fully evaporated after coating or the operating environment has poor ventilation.


If the curing curve cannot be executed according to 300℃ × 2 hours or the heating rate is uncontrollable.


If the rubber layer thickness cannot be controlled, too thick or local accumulation.


If the operating temperature exceeds 325℃ for a long time or there is local overheating, the upper temperature limit has not been evaluated.


If the sealing structure can withstand high pressure, strong vibration or large displacement, and actual working conditions have not been verified.


Contact with strong oxidation, gas corrosion or special media, and the stability of the adhesive layer has not been verified.


Specific airworthiness, military or other industry approvals are required, but corresponding documents have not been obtained yet.


Only the operating temperature is known, without data on substrate, adhesive layer thickness, curing curve and sealing structure.


The customer requests to directly mix it into the in-use system, but cannot control the surface treatment, dilution, coating and curing conditions.


When switching from phosphate, borosilicon nitrogen, polycarbon silane or other silicone resin sealants, the process has not been re-adjusted.


Storage conditions do not meet the requirements of cool and dry, sealed, or exceed a 6-month shelf life.


The safety factor and actual cycle times for 400℃ aging for 50 hours and thermal shock for 50 times have not been evaluated.


IX. What selection support can our company provide?


As a provider of the entire organic silicon value chain solutions, our company can assist in comparing the applicability of silicone oxygen-based sealants in different substrates, adhesive layer thickness, curing curves and thermal cycling conditions for product H1400.


For projects that need to ensure high-temperature sealing between engine blades and hubs, control of solvent evaporation, no cracking or powdering of the adhesive layer, and thermal shock stability, before selection, the following information should be provided:


Application direction and substrate type.


Target long-term temperature, peak temperature and local overheating conditions.


Surface treatment method and sealing gap.


Adhesive dilution, solvent evaporation and coating process.


Adhesive layer thickness and curing curve.


Operating atmosphere, oil mist, gas and thermal shock requirements.


Sealing structure pressure, vibration and displacement conditions.


Current sealant model, process and failure performance.


Acceptance method and applicable standards.


After receiving complete materials, it can be determined whether to prioritize testing a certain dilution, coating and curing scheme of product H1400, or to choose a phosphate, borosilicon nitrogen, polycarbon silane or other high-temperature sealant route.


X. Common Misconceptions


A product with a long-term service temperature greater than 325℃ can be used at higher temperatures for full load operation for a long time.
The information given states that there is no cracking or powdering after 50 hours of aging at 400℃, but long-term use still requires assessment based on actual temperature, time and safety factor, and cannot be judged solely based on the temperature resistance marking.


Products with solvents can be thickly coated and then cured at high temperatures.
The solvent needs to fully evaporate, and rapid heating or thick adhesive layer can cause blistering, pinholes and cracking. The coating thickness and curing temperature curve need to be controlled.


The higher the curing temperature, the stronger the adhesive layer.
The curing should be carried out at 300℃ for 2 hours. Exceeding the recommended curve may result in the adhesive layer being too brittle, damage to the substrate or a decrease in adhesion.


The thicker the adhesive layer, the more reliable the sealing.
A thick adhesive layer will increase the difficulty of solvent evaporation and thermal mismatch, and is more prone to cracking or powdering. The thickness should be optimized according to the sealing gap.


Compatibility with the substrate means direct coating.
The surface must be cleaned, solvent evaporation, adhesive layer thickness, curing curve, operating atmosphere and thermal shock conditions still need to be confirmed.


Appearance at 25℃ is the same can be replaced in equal amounts.
Different high-temperature sealants have different temperature resistance, curing behavior, solvent content and thermal shock performance. Replacement requires re-verification.


Product H1400 can be used for all engine high-temperature sealing.
This product is suitable for high-temperature sealing between engine blades and hubs. For higher temperatures, strong oxidation, high pressure or special airworthiness requirements, it is necessary to conduct special verification or choose other materials.


The smell of the product can be ignored.
The product contains solvents, and it should be used in a ventilated environment and protective measures for operators should be taken.


The product can be directly used after 6 months of storage.
The shelf life is 6 months. After expiration or improper storage, the material state, viscosity and curing performance should be re-tested.


XI. Recommended Selection Steps


Confirm the application direction: high-temperature sealing between engine blades and hubs.


Confirm the substrate type, surface treatment and sealing gap.


Confirm the adhesive state, viscosity and storage period.


Confirm the solvent dilution, evaporation conditions and coating process.


Confirm the thickness of the adhesive layer and the curing curve at 300℃ for 2 hours.


Confirm the usage temperature, atmosphere, thermal shock and vibration conditions.


Select product H1400 or other high-temperature sealants based on the application scenario.


Set different adhesive layer thicknesses, dilution ratios and curing curve gradients for small-scale tests.


Test the appearance, adhesion, no cracking, no powdering and sealing performance of the adhesive layer.


Carry out 400℃ aging, thermal shock from room temperature to 400℃ and actual structural sealing verification.


Evaluate the consistency of the adhesive material state and high-temperature performance between batches.


Confirm that ventilation, moisture-proof and storage conditions are in place.


After completing multiple batch and actual working condition validations, determine the official usage plan.

Online QQ Service, Click here

QQ Service

What's App